對于26噸壓路機的維修保養十分重要，但是由于技術保養人員對保養工作存在的誤區，致使26噸壓路機性能更加不良。下面冷再生機租賃廠家從五個方面為您講解一番：

The maintenance and upkeep of the 26 ton roller is very important, but due to misunderstandings among technical maintenance personnel, the performance of the 26 ton roller is even worse. The cold regeneration machine rental manufacturer will explain to you from five aspects:

1

one

潤滑油定期地更換沒有及時做到

Regular replacement of lubricating oil not achieved in a timely manner

像26噸壓路機這樣的重型機械，由于長期在重負荷的環境下工作，機械零件的磨損是比較嚴重的，而潤滑油是保證其機械磨損降至正常狀態下的重要因素，也是保證26噸壓路機正常工作的重要因素，26噸壓路機在長期使用中，會導致機體的內部、油底殼中含有大量的機械磨損雜質，另外，長期使用的潤滑油，若不及時更換，其中也會含有大量雜質，這樣的狀況既有可能會導致機械的磨損更加嚴重，因此，因此潤滑油的不及時更換對機械的損害是很嚴重的。

Heavy machinery such as a 26 ton roller, due to long-term operation in a heavy load environment, has severe wear and tear on its mechanical components. Lubricating oil is an important factor in ensuring that its mechanical wear and tear are reduced to normal conditions, and it is also an important factor in ensuring the normal operation of the 26 ton roller. Long term use of the 26 ton roller can cause a large amount of mechanical wear impurities to be contained in the internal parts of the body and the oil pan. In addition, Long term lubricating oil, if not replaced in a timely manner, may also contain a large amount of impurities, which may lead to more severe mechanical wear. Therefore, the failure to replace lubricating oil in a timely manner can cause serious damage to the machinery.

2

two

維修時對螺栓非正常操作以及輪胎氣壓控制不到位

Abnormal operation of bolts and inadequate control of tire pressure during maintenance

維修人員在26噸壓路機的維護保養工作中起到了為直接的作用，但是，一些維修技術人員在養護過程中，為了確保機械構件之間連接的穩定性，常常會將螺絲擰的過緊，或者是將輪胎的氣壓充的過足，這樣的出發心態也是求得安全穩定，但是負面影響較為明顯，機械銜接過于緊密、會造成螺栓的斷裂滑絲現象，氣壓過高會造成輪胎張力過大，是十分不利于26噸壓路機的正常使用的，存有一定的安全隱患。

The maintenance personnel have played a direct role in the maintenance and upkeep of the 26 ton road roller. However, some maintenance technicians often tighten the screws too tightly or inflate the tire pressure too much during the maintenance process to ensure the stability of the connection between mechanical components. This mentality also seeks safety and stability, but the negative impact is more obvious. The mechanical connection is too tight It can cause bolt breakage and slipping, and excessive air pressure can cause excessive tire tension, which is very detrimental to the normal use of a 26 ton roller and poses certain safety hazards.

3

three

26噸壓路機水箱溫度控制不當

Improper temperature control of the 26 ton roller water tank

26噸壓路機的水箱溫度控制直接影響到水箱設備――缸體的性能及耐久性。但是在工程運行過程中，機械的持久運行勢必會消耗大量的水，往往在向水箱中加水的時候，水箱內的水溫是十分高的，通常都是出于沸騰狀態的，這時候，由于技術人員對水溫落差的忽略，驟加冷水，導致水箱溫度急劇下降，冷熱的急劇變化，對箱體缸體是十分不利的，大大降低了其耐久性。

The temperature control of the water tank of a 26 ton roller directly affects the performance and durability of the water tank equipment - the cylinder body. However, in the process of engineering operation, the sustained operation of machinery will inevitably consume a large amount of water. Often, when adding water to the water tank, the water temperature inside the tank is very high, usually in a boiling state. At this time, due to the neglect of the water temperature drop by technical personnel, sudden addition of cold water leads to a sharp decrease in the temperature of the water tank, and the rapid changes in cold and hot water are very detrimental to the cylinder body of the box, greatly reducing its durability.

4

four

潤滑油脂的不正確使用

Incorrect use of lubricating grease

26噸壓路機的設備中，各自有其特殊的要求，其中，汽缸墊對密封性有高的要求。但是在安裝汽缸墊的時候，是有高的要求的。一些技術人員在安裝的時候，為了保證安裝的順利，往往會涂抹潤滑油脂，在氣缸蓋螺栓擰緊的時候，由于物體間的擠壓，部分潤滑油脂會進入到汽缸水道中，氣缸中的溫度是高的，這樣的話，油脂長期處于高溫狀態下，易碳化，碳化的后果會損壞汽缸墊，接著變會引起氣缸的漏氣，后果不堪設想。

Among the 26 ton roller equipment, each has its own special requirements, among which the cylinder gasket has high requirements for sealing. But when installing the cylinder gasket, there are high requirements. Some technical personnel often apply lubricating grease during installation to ensure smooth installation. When tightening the cylinder head bolts, due to the compression between objects, some of the lubricating grease will enter the cylinder water channel, and the temperature in the cylinder is high. In this way, the grease will be in a high-temperature state for a long time, which is prone to carbonization. The consequences of carbonization will damage the cylinder gasket, and then cause air leakage in the cylinder, which is unimaginable.

5

five

液壓系統方面的操作及油品選擇不當

Improper operation and oil selection in the hydraulic system

燃油的選擇直接決定發動機的工作性能及效率，26噸壓路機往往選擇的是輕柴油，輕柴油也有不同的等級型號，不同的型號使用上性能差別很大，但是一些技術人員在選擇時往往考慮不周，導致選擇了不適合的油，給后期的養護帶來了不少困難。液壓系統是其工作中的核心系統，這里對系統頻率的控制，機械馬力的控制，對機械的性能耐久關鍵，操作的馬虎不當對機械的長久運行是十分不利的。

The selection of fuel directly determines the working performance and efficiency of the engine. 26 ton road rollers often choose light diesel, which also has different grades and models. The performance of different models varies greatly, but some technical personnel often do not consider the selection carefully, leading to the selection of unsuitable oil, which brings many difficulties to later maintenance. The hydraulic system is the core system in its operation, and the control of system frequency and mechanical horsepower is crucial for the durability of mechanical performance. Improper operation is very detrimental to the long-term operation of the machinery.

使用說明書中對壓路機的等級養護分為一二三級，一級保養工作類似于走合期保養，主要對機械部件之間的連接，潤滑狀態及時更新，排除工作一段時間后的薄弱環節。二級保養主要的工作時檢查和調整，這時候的檢查調整是全面的，主要目的是保證設備在較長的一段時間內有一個良好的狀態。三級保養工作時細致入微的，要將設備全盤拆卸，整體清洗，整體潤滑，及時更換，也會附加一些維修工作，保證設備發揮其價值。更多需求就來我們網站http://www.drkallas.com咨詢了解吧！

In the user manual, the level maintenance of the roller is divided into one, two, and three levels. The first level maintenance work is similar to the maintenance during the running in period, mainly updating the connection and lubrication status between mechanical components in a timely manner to eliminate weak links after working for a period of time. The main task of secondary maintenance is to inspect and adjust, which is comprehensive and aims to ensure that the equipment is in good condition for a long period of time. During the third level maintenance work, the equipment should be thoroughly disassembled, cleaned, lubricated, and replaced in a timely manner. Additionally, some maintenance work will be added to ensure that the equipment can fully realize its value. Come to our website for more needs http://www.drkallas.com Consult and understand!